Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
We have noticed this article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and thought it made good sense to discuss it with you over here.
Installing a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a reasonably hard task. If the old tub is readily available, the project can relocate immediately; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is much better to consider employing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will certainly assist you mount a brand-new tub in your shower room if you have already purchased a new tub as well as don't need to transform the arrangement of your previous water system pipes.
Your devices and also product list should comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines are in place between the faucet as well as the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former kind needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Using the two wood boards under its feet, position the bath tub in the required position. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the water and also examine all joints and brand-new pipework for leakages and also tighten them if needed. Fill the tub as well as likewise check the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bath tub should wait until the tub has actually been made use of at the very least once as this will settle it into its final setting.
Getting ready for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, causing difficulties with moisture as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on another domain. You should set aside a second to distribute this article if you enjoyed it. Thank you for your time. Visit again soon.
Call Today Report this page